| EUROPA PRICING |
|---|
| Brackets | Width | 5'3" | 6'11" | 8'7" | |
|---|
| 2 | 5' | - | - | - | List Price |
| - | - | - | Sun Boss
Price |
| 2 | 6' | - | - | - | List Price |
| - | - | - | Sun Boss
Price |
| 2 | 7' | $ 1284.44 | - | - | List Price |
| $ 963.33 | - | - | Sun Boss
Price |
| 2 | 8' | $ 1368.89 | $ 1428.89 | - | List Price |
| $ 1026.67 | $ 1071.67 | - | Sun Boss
Price |
| 2 | 9' | $ 1440.00 | $ 1500.00 | - | List Price |
| $ 1080.00 | $ 1125.00 | - | Sun Boss
Price |
| 2 | 10' | $ 1511.11 | $ 1584.44 | $ 1631.11 | List Price |
| $ 1133.33 | $ 1188.33 | $ 1223.33 | Sun Boss
Price |
| 3 | 11' | $ 1595.56 | $ 1644.44 | $ 1728.89 | List Price |
| $ 1196.67 | $ 1233.33 | $ 1296.67 | Sun Boss
Price |
| 3 | 12' | $ 1668.89 | $ 1728.89 | $ 1824.44 | List Price |
| $ 1251.67 | $ 1296.67 | $ 1368.33 | Sun Boss
Price |
| 3 | 13' | $ 1728.89 | $ 1811.11 | $ 1908.89 | List Price |
| $ 1296.67 | $ 1358.33 | $ 1431.67 | Sun Boss
Price |
| 3 | 14' | $ 1811.11 | $ 1884.44 | $ 2004.44 | List Price |
| $ 1358.33 | $ 1413.33 | $ 1503.33 | Sun Boss
Price |
| 3 | 15' | $ 1691.11 | $ 1835.56 | $ 1968.89 | List Price |
| $ 1268.33 | $ 1376.67 | $ 1476.67 | Sun Boss
Price |
| 4 | 16' | $ 1944.44 | $ 2040.00 | $ 2195.56 | List Price |
| $ 1458.33 | $ 1530.00 | $ 1646.67 | Sun Boss
Price |
| 4 | 17' | $ 2028.89 | $ 2111.11 | $ 2280.00 | List Price |
| $ 1521.67 | $ 1583.33 | $ 1710.00 | Sun Boss
Price |
| 4 | 18' | $ 2111.11 | $ 2208.89 | $ 2375.56 | List Price |
| $ 1583.33 | $ 1656.67 | $ 1781.67 | Sun Boss
Price |
| 4 | 19' | $ 2195.56 | $ 2280.00 | $ 2460.00 | List Price |
| $ 1646.67 | $ 1710.00 | $ 1845.00 | Sun Boss
Price |
| 4 | 20' | $ 2268.89 | $ 2351.11 | $ 2604.44 | List Price |
| $ 1701.67 | $ 1763.33 | $ 1953.33 | Sun Boss
Price |
| Europa prices include hardware, fabric, universal mounting brackets and hand crank. All frames are powder coated cream or white. Motors are recommended for widths of 18' and over. |
|
This product must be mounted into either a wood fascia board, studs or "header" above the door (unexposed header underneath stucco wall is acceptable). Measure the width of the opening and add at least 12" to that dimension. It can be wider if you choose. There are three (3) arm size projections: 5'3", 6'11" and 8'7".
Measure the desired projection area and pick one of the six projection arm sizes. Take into consideration where the retractable is to be mounted; the fascia, wall, or roof. Also, consider that if mounting on the fascia, you need at least 6" of an area to mount on to.
- Awning width will be manufactured to exact custom sizes. The price is based on the next largest foot increment. See pricing guide.
- No permits are needed for this product.
- Make sure the area where the awning is to be mounted is clear of all obstacles, light fixtures and eave overhangs.
How To Install Europa Retractable Patio Cover
Tools needed:
- Electric drill
- Hammer Socket set with 9/16", 1/2" and 11/16" drives
- Level
- Tape Measure
Follow these simple directions to insure an accurate, secure installation of your new Retractable Patio Cover:
- Lay the unit on the ground below the mounting area.
- Determine where the awning is going to be mounted, remembering to find the header or studs, or mount on fascia board.
- Space the supplied mounting brackets evenly across the width of the awning and install each bracket. Make sure brackets are installed exactly on the same plane across the width of the awning. Use two (2) 3/8" x 4" lag bolts and 1" washers for each bracket. Make sure each bracket is tight against the wall and level to the ground.
- Simultaneously lift the entire awning and slide back bar into the mounting brackets. Install 1/2" x 3" locking nut. Bolt through the front of the bracket. Do not leave the awning or move it until all brackets have been secured with this nut and bolt.
- Roll out awning to its full projection, using either the hand crank or motor. Adjust it to the desired level using an 11/16" ratchet on the single bolt pitch adjustment, located under the arm support. Rotate the bolt clockwise to raise the pitch and counter clockwise to lower the pitch.
- Crank or motor the awning in and out several times to familiarize yourself with how the awning should look when completely projected. Fabric should always roll out from the top of the roller tube and never from the bottom. Awning is fully projected when the arm elbow locks. If the awning is rolled out any further than this, the fabric will become loose.
- If the valance is not already installed, remove (1) end cap of the front bar with a Phillips head screwdriver, slide the valance into the slot, then replace the end cap.
|
|
